PDA

View Full Version : Found VGA DSUB Backplate for Zorro/PCI



arnljot
29th April 2009, 19:45
Title is pretty descriptive isn't it?

And in case it's not, then I have to draw you a picture:
http://www.arnljot.com/images/wtbpciplate.jpg

Zetr0
2nd May 2009, 00:31
I will have a route round in a box or two Ar9 PM me your deets buddy :)

arnljot
2nd May 2009, 01:21
Deets pm'ed :)

arnljot
20th May 2009, 17:43
Did you find any Z?

Zetr0
20th May 2009, 18:07
bare with me chap.... very busy atm!

arnljot
21st July 2009, 22:45
BUMP

Not too soon I hope?

arnljot
1st October 2009, 23:07
BUMP

Anyone?

meega
2nd October 2009, 11:53
I'll have a look through my boxes of bits... I know I've got some blanking plates... I also have a few old cards with such things still attached and I'm not averse to splitting the plate in most cases...

Give me a little time to find the various collections, I'm sure there'll be something close to what you want.

meega
10th October 2009, 09:17
Teh ones I've found so far are not right, unless you want a blank so that you can drill your own cut-out... I'm still looking for a box of old cards, but they might have been chucked a while ago (not even I keep everything for ever).

arnljot
12th November 2009, 21:32
Close this thread - I think...

I'm going to dremmel it, I think.

Also, this can be our "and our apologies to Matt Damon, sadly there was no time for him today".

rkauer
13th November 2009, 00:14
As you wish, sir.

rkauer
11th January 2010, 17:29
Thread re-opened as Kin's request.

arnljot
11th January 2010, 18:19
wtf?? :o:lol::p

rkauer
11th January 2010, 20:38
He PM'ed me asking to re-open the thread as he found a possible solution for your problem.

jvdbossc
11th January 2010, 20:40
most of the ones i've got are probably in the middle, where you drawed arnjlot. Not ok? I think most of the cards have them right in the center, where it is most logic, have a couple of dumpster not pci, with tv out etc.. might be one have a look tommorrow since they are not in a lighted place.

Why don't you just go to the dumbster?:D

If you succeed in Dremel that...:bowdown:

arnljot
11th January 2010, 21:01
@rkauer, I know - he PM'ed me. I just wanted to have a little fun and confuse you MODS :-) :lol:

@jvdbossc, I dunno if such a thing would work. The one I have where it says bad crashes with the Mediators power connector. After Kin has showed me his magic plate, I'll let this thread know :-)

Kin Hell
12th January 2010, 02:04
This needs two holes drilling for a VGA port & you should be good to go m8y. Any good for ya?

The measurement from the underside of the bracket to the first edge of the hole is 30mm & the hole is 20mm.

Kin

jvdbossc
12th January 2010, 08:17
the ones with other outputs have there connector on the bad position. so can't help

arnljot
12th January 2010, 10:17
@kin

When I come home I'll meassure the CVPPC connector and see if it'll fit your 20mm hole :-)

Kin Hell
12th January 2010, 13:19
No need to m8. Your CVPPC Port is a standard VGA 15 pin port as found on most VGA cards. The bracket just needs 2 holes for the securing Castle Nuts & you should be good to go. :thumbsup:

Kin

arnljot
12th January 2010, 13:19
Then I'll PM you and ask you for your price :-)

Kin Hell
12th January 2010, 13:32
No need m8. It's yours for free. :thumbsup:

Kin

arnljot
12th January 2010, 13:35
Thank you!! You've got my address on PM mate!

arnljot
19th February 2010, 20:06
Not sure what I should do? Bump or ask for it to be closed again? :-(

Kin Hell
20th February 2010, 04:50
You dont need to do either Arnljot & you should have PM'd me for an earlier update.
I've been a total jerk & not posted it yet. :Doh:
It did go to the post office with me on one occasion, with another parcel for Zetr0 & it wasn't my normal post office. They didn't have a small enough Jiffy Bag, so I didn't send it. Since then, I've been bombed out on the kitchen Extension & had some real continuous bad health with Flu & Sinus infections.

It's still sat on my desk here collecting dust, so I'll get on it this week for you; - I promise. :nod:

HugZ fella,

Charlie

Kin Hell
22nd February 2010, 17:06
It went via AirMail First Class this morning m8. Let me know when you have it. :thumbsup:

Kin

Kin Hell
7th March 2010, 10:20
Three posts in row......:unsure:

Is it there yet m8?

Charlie

arnljot
10th March 2010, 08:04
Yes, it arrived a few days ago. So no I have no exuses to work on my miggy.

+ Feedback left! :)

Kin Hell
10th March 2010, 09:58
Good stuff fella. :thumbsup:

Charlie

TheCorfiot
10th March 2010, 18:55
Nice :thumbsup:

Thread Closed
TC :)