PDA

View Full Version : Info needed on PCI card



Jebi1717
14th July 2012, 11:12
Anyone have any info on a PCI graphics card.

Model EV-3DS3-4

It has 15 pin SVGA
It appears to have 2mb Ram
Elephant Rom Chip.
S3 Virge /DX on Board
34 pins with FC written on top
10 pinds with J2 written on top/

Would this work on Mediator 1200 PCI ?

Will post a picture later.

If anyone has a manual that would be great.

https://dl.dropbox.com/u/16264024/Photo0479.jpghttps://dl.dropbox.com/u/16264024/Photo0480.jpghttps://dl.dropbox.com/u/16264024/Photo0482.jpg

johnim
14th July 2012, 11:20
S3graphics pci vga card sc virge/dx 86c375

did quick search and found this

look here is should work fine

http://www.elbox.com/mediator_driver_guide.html

all info for mediator can be found in my thread

http://www.amibay.com/showthread.php?t=11993

Jebi1717
14th July 2012, 11:25
Thanks Johnim.

So It will work.

Any ideas on the specs.

Does it have the capability of adding a pc Floppy and Pc serial

johnim
14th July 2012, 11:28
Does it have the capability of adding a pc Floppy and Pc serial no mate not at all


just 2 mb

look for a voodoo3 2000/3000 for best mediator usage mate

or radeon 9200 or 9250 64/128mb

BLTCON0
14th July 2012, 12:40
@Jebi1717
Are you sure the FC connector is 34 pins and not 26 pins?
"FC" stands for "Feature Connector", nothing to do with floppies. It was typically found on PCI and early AGP graphics cards, supposedly for stuff like MPEG playback modules etc.
No idea on the 10-pins J2, but if it is jacketed it's 99% meant for connecting a cable, if it's bare it could just be a configuration jumpers block, although I've never seen any PCI card with that many.

roy_bates
14th July 2012, 13:11
ive got a 4mb version of these pci cards and it works.

the fc connector is a feature connector for mpeg module,mines an s3 virge 86C235.
the card has the same performance as a CV64 3D card for zorro amiga's that uses the same virge chip.
but youll probably be better off with a voodoo3 or a radeon.

Jebi1717
14th July 2012, 17:33
As you can see the 34 pin FC and 10 pin J2 are top of the card. There is a trace either burned out or rusted. I have not tried the card yet.

roy_bates
14th July 2012, 17:47
i think the card will still work,even with that burned trace.(where its burned it dont seem to go anywhere past that connector at j2)

it goes round the front of the card under the vga port past j4 on the card out the other side of the card to the pci slot.


are you sure its a 2mb card? all the spaces for memory are filled to max

Jebi1717
14th July 2012, 18:09
Thanks for that

Each chip end with 256a so I guess thats 8 x 256k which is 2meg

thanks again.:thumbsup:


Please close..

Jebi1717
15th April 2013, 10:48
Can you please close this thread. !!!

AndyLandy
15th April 2013, 12:15
Looks like a plain-Jane S3 Virge VGA card to me. I used to have a stack of the things once upon a time. Should work with most Amiga PCI solutions.


Can you please close this thread. !!!

No need to close threads in AmiOracle.

:thumbsup: