Printable View
At this point you should be looking at getting the system stable before throwing down hacks to get more speed.Quote:
Originally Posted by abraXXious
the 040@25Mhz will give you 18.1 MIPS compared to 9 MIPS of a 40mhz 030 - however this assumes FAST ram is installed on both machines.
If you are struggling to attain 18.1 MIPS then there is either a hardware or software issue that should be inspected.
I think it should just be a case of going to Prefs / Trident, clicking on controllers, and setting your device to either "denebpiousb.device" or "denebdmausb.device"Quote:
Originally Posted by abraXXious
I have five A4000's. I know how you feel as I have had some issues with them. But I think you might have a lemon on your hands. All 5 of mine work fine and when you know what the achilles heel is with them, it makes dealing with them easier.
I know that the 4000 is more prone to problems and I think the main reason is the battery leaking and the CPU fast slot design. The battery is in an area that if it leaks a tiny bit, will cause issues! (The 2000, on the other hand, can have the battery leak bad and the system will usually be just fine) and since the system does not have an on board CPU, it needs to have a CPU daugter card installed. So if there is an issue with the card or connection, you will have issues.
Some things that can cause issues (as was previously mentioned)
1. Leaky battery issues:
Make sure you remove any leak prone batteries and if even a small amount has leaked, clean it thourougly! From my experience even a small leak will cause issues with the system. Mostly RTC and SIMM issues. Look over the area to make sure there are no broken traces.
2. CPU Fast Slot issues:
The CPU card slot sucks. On my A3000T and some 4000's I have to constantly reseat the CPU card to get the system to boot. Might be bad solder connections or bad socket. But on some it's just a matter of the CPU card not seating properly in place. One of mine only has 2 of the 4 plastic posts that snap on. I think this is the most common problem I have seen with all the 4000's I have dealt with.
3. SIMM issues:
Seems the Chip RAM slot can cause issues so check it out. Also the Fast RAM slots are prone to the clips breaking so the SIMMs will not sit firmly in place. Also check to make sure there was no battery leakage.
These are the most common things I have seen. But it seems your board might have issues beyond that. Maybe look into just getting another A4000 motherboard. I know, they are pricey...
Good luck :thumbsup:
:) I have two a4k mbs - both in pristine (to look at) condition.
Neither board has had bad battery leakage. Both boards have had caps replaced, button batteries installed, rcas replaced, joy/mouse ports replaced, op amps replaced and both boards have been resealed with pcb lacquer. One boards has even had all the simm sockets replaced with high quality metal clip units.
These boards are probably the cleanest you will ever see. I think the problem is either a hardware conflict or faulty simm module.
Anywho, the "modified" system has been up and running all night with no crashes. Its specs are now:
a4k Mb with special 3.9 ks roms and 16 mb fast
a3640 (not overclocked - yet) - down from Cyberstorm Mk III 060 with 128 mb fast
DKB 3128 with 128mb fast
Deneb USB card (only works in Z II mode at the moment)
Spectrum 24 2mb Gfx Card - down from Cybervision 64/3d with Scansoubler Module
LG IDE DVD Burner
8Gb Compact Flash Card on Compact Flash to IDE adapter
OS 3.9 with Boingbags 1 & 2 installed
I was expecting the 040 to be a quarter the speed of the 060, but it "feels" 1/8th!
Also, since I no longer have any scan doubler attached, can anyone suggest a good mode promoter?
Oh, and with the 040, should I change the math libs? Change any system libs etc? Install Oxypatcher etc? Oh, and should I be using some form of Maprom option? I know there is a jumper for Maprom on the 040 but how is it used?
Thanks.
@abraXXious
Some pics showing PicassoIV config on my TV-Monitor LG M23620-PZ
Attachment 8595 Attachment 8596 Attachment 8597
Attachment 8598 Attachment 8599 Attachment 8600
I work at 1024x768 24 bit.
Higher resolutions works but I need to configure manually "centering" & "size" (Monitor Menu), this is because PicassoIV is not designed to work at higher resolutions in non-interlaced modes.
I have found an archive on Aminet called QuickRom which copies your kickstart rom to fastram on boot up to increase speed. Is these any point to this when running os 3.9? I thought 3.9 already copied itself to ram as it reads the rom image from disk. Can someone please clarify this?
Also, found CopyMem, which includes an 040 version of CopyMemQuick, will this help?
Since you have the ROM in ROM, and not loaded to memory, there will be slow downs due reading it on the fly any time one of its modules are requested. Problem is the 3.9 ROM is 1Mb, so old kick-2-RAM programs will fail miserably.
Also, the slow running system may indicate a fault on the CPU socket.
@abraXXious
About your DKB 3128 check if.....
Quote:
- four 72 pin SIMM sockets accept 128 MB RAM
- supports 4, 8, 16, 32 MB SIMMs 80 ns or faster
- when different size of SIMMs are installed the "3128" program has to be added to the beginning of the Startup-Sequence - otherwise the system will assume that every SIMM is as large as the largest one
- if used with a Commodore A3640 processor board, that must be at least revision 3.1
And about DENEB... maybe this helps you....
Attachment 8603
If you don't use a CS 060, I think is better to grab standard 040 libraries in the FlashROM of the DENEB. Remember.... update to V9 firmware.
@abraXXiousQuote:
Originally Posted by merlinkv
I just noticed on your other thread that you had no 68040.library installed until now. You may want to try your Deneb in PIO or DMA mode again, I had the same issue until last night when I tried overwriting my own 68040.lib with one from the Phase5 website. I'm also using an A3640 so I'm not sure if I should be using ths version, but it does seem to have solved a lot of problems for me including now being able to run my Deneb in PIO and DMA modes.
Thanks lewism - just tried the Deneb again in Z 3 mode and its working. From what I can tell, PIO mode is almost as fast as DMA mode, just more cpu intensive, but PIO is supposedlt more stable, so I left mine on PIO.
Just to endorse post #59 by lewism;
Without the correct 040 Libs in place, you're gunno crash more than windows 98 trying to use USB.
As Zetr0 said earlier, look at Oxyron Patcher & such programs when you are stable. ;)
Kin
Stable for 9 hours straight installing and running all sorts of software. Even things like Sid4Amiga, which can be picky, is running perfectly.
So, in your own words.....Quote:
Originally Posted by abraXXious
What was it? :lol:
Kin
Well, it wasnt crashing in the first place, it was just sloooow. Missing 68040.library and caches not switched on.
I have one perculiar problem though, when I right click on an icon and choose format the system locks, not crashes (mouse still moves etc), but locks - cannot load/run any programs.
Like an intuition lock up.
Strange thing is that if I run Format from the icon it is fine?!
Any ideas?