A1200 + M-Tec1230LC + 4mb + 4GB CF-IDE (Also splitting)

Hi!

I'm selling one of my spare A1200's comes fully setup with 4gb CF-IDE and M-Tec 1230LC (030 @ 40mhz) & 4mb Ram so ideal for WHDLoad and gives the A1200 a nice boost!

The A1200 is in good condition (clean but some yellowing to keys) There is a gap in the case where IDE leads were routed to an external CDROM, I'll take a Photos later.

It has 3.0 Roms and Classic Workbench Lite installed, Original 3.0 Disks included in the sale. Motherboard is Rev2B.

I think the Motherboard needs a re-cap as it dosen't always boot first time so please bare this in mind - once running it seems to be stable!

I'm looking for £135 + P&P (N/A as A1200 now reserved) I will include a PSU & Mouse if needed.

As said pics to come later.

Shipping will be £12 in UK and £28+ in EU but up to £70 outside EU!

*UPDATE*

Now splitting

M-Tec 1230LC 4mb Ram (Full 030+MMU @40mhz) = £85 + P&P (Sold to Philran)
A1200 with 3.0Roms = £35 + P&P (as spares repairs) (No Mouse/PSU) (Sold to Zetr0)
4gb CF Card + CF-IDE adapter/cable with Workbench 3.0 Disk Set = £35 + P&P (No longer available)

Quote:

---

Originally Posted by fitzsteve

I think the Motherboard needs a re-cap as it dosen't always boot first time so please bare this in mind - once running it seems to be stable!
EU!

---

Not interested, but nice system :thumbsup:

If you get the rom screen, that's caused because of 3.0 roms and hard disk not fast enough. I have one amiga 1200 with 3.0 roms does the same. (is normal)

Quote:

---

Originally Posted by jvdbossc

Quote:

---

Originally Posted by fitzsteve

I think the Motherboard needs a re-cap as it dosen't always boot first time so please bare this in mind - once running it seems to be stable!
EU!

---

Not interested, but nice system :thumbsup:

If you get the rom screen, that's caused because of 3.0 roms and hard disk not fast enough. I have one amiga 1200 with 3.0 roms does the same. (is normal)

---

Hi My friend!

Thanks for the advice, it had a yellow screen until reseating the M-Tec and then sat at black screen. After 'warm up' it booted fine.

Last time used it booted first time but I suggest a re-cap.

Otherwise seems ok! Buyer could always swap out the main board if they can't do the work :)

Steve.

Some pics for you! I need to find a floppy power cable in my spares box, you can see in the pics that is missing but will be included. Mouse shown is not the one included, it will be a standard A1200 mouse!

PS. board seems to be booting normally now! Maybe Accelerator was just not properly seated or dirty? I cleaned contacts with IPA ;)

Now splitting

M-Tec 1230LC 4mb Ram (Full 030+MMU @40mhz) = £85 + P&P
A1200 with 3.0Roms = £35 + P&P (as spares repairs) (No Mouse/PSU) (Reserved for Zetr0)
4gb CF Card + CF-IDE adapter/cable with Workbench 3.0 Disk Set = £35 + P&P

@Stevie

I am interested in the A1200 =)


PM on route

Quote:

---

Originally Posted by fitzsteve

Some pics for you! I need to find a floppy power cable in my spares box, you can see in the pics that is missing but will be included. Mouse shown is not the one included, it will be a standard A1200 mouse!

PS. board seems to be booting normally now! Maybe Accelerator was just not properly seated or dirty? I cleaned contacts with IPA ;)

---

Nice system Steve,you make me want to get a 1200 again...

Quote:

---

Originally Posted by Zetr0

@Stevie

I am interested in the A1200 =)


PM on route

---

Will PM back shortly (busy at work) but A1200 reserved for you!

Quote:

---

Originally Posted by Megamix

Nice system Steve,you make me want to get a 1200 again...

---

:)

My Hero! :inlove:

( thank you =) )

I am declaring my interest in the memory board. Will PM direct.

Phil