Closed CyberstormPPC with 060/50, 604e/233 + 128 Mb RAM as CyberstormMK3 - Read carefully!

[sax]

For sale my Phase 5 Cyberstorm PPC card with 128 Mb EDO RAM.

features:

• PowerPC 604e @ 233 MHz
• 68060 @ 50 MHz (rev.1) with MMU and FPU
• 4 x 32 Mb same type HP memory with 64 bit interleaved RAM access
• Ultra Wide SCSI controller (NCR 53C770) about 40 Mb/s read-write
• expansion slot for the CyberVision PPC
• with original CSPPC heatsink with quiet fan

The card is tested, I have been using it for several years with Sonnet PPC in MK3 mode without any errors. As you can see in the pictures, it works with the CyberVisiion PPC video card, SCSI runs even with the slower HDD at a speed of 30 Mb/s with minimal CPU load, 128 Mb of very fast memory is available. There were issues with the PPC part, especially after using OS4, the PPC processor sometimes "disappeared". Now it works properly, as you can see in the pictures, I think later it needs a better heatsink+fan, recap or reflow. It has an original CSPPC heatsink, it might not be enough for it.
I never had a problem with 68k side, I didn't use the PPC part very much. That's why I'm selling as CSMK3.

There is no box or manual, only the card, which is in the condition shown in the picture !
CSPP and SCSI HDD are not part of the sale, they were only connected for testing!

I can ship worldwide, but Europe preferred. Outside of Europe, I send only at the buyer's responsibility and with substantial insurance!

price: €1650 + PP + shipping (can pay as friend, and then there is no PP commission or bank transfer is also possible.)

 

[sax]

Videos not longer available.

 

[sax]

Now I advertise elsewhere.

 

[sunmax]

Interesting accelerator! Does its 060 comes with FPU ?

 

[Timtheloon]

Interesting accelerator! Does its 060 comes with FPU ?

@sunmax the 060 FPU is shown running in the screenshots

 

[sax]

Yes, but the letters are quite small, hard to notice. So the 060 processor contains both MMU and FPU. I will correct it in the ad!

 

[sax]

Thanks Sunmax for bringing it to my attention!

 

[sax]

I am now accepting close offers.

 

[dframeli]

Declaring interest, pending response to PM…

 

[sax]

PM sent to dframeli.
Sold to dframeli.
Payment details sent, waiting for money.
The money came through, but unfortunately not in the agreed currency. :-(
Refund sent to dframeli, he will send again in USD.
The transaction failed due to card failure. The money was refunded.

 

[Milesunder]

Declaring interest.

 

[sax]

Unfortunately, the card dead during the last testing before shipping. :*-( It is currently under service. If it can be fixed, Dframeli is first in line, Milesunder is the second.

PM sent to Milesunder.

 

[dframeli]

Interest withdrawn. (was previously declared here)

 

[gerul]

Declaring interest.

---

What it the status of the card? And the interest queue? I'm declaring interest if card is in working condition

 

[sax]

While it is still under repair, unfortunately the cause of the error has not yet been found.

 

[mgfalc]

Declaring interest.

---

Declaring interest, pending status of repair

 

[sax]

An X-ray was taken, but unfortunately it did not show the cause of the error (the resolution was not enough)
I'm looking for another x-ray..

 

[Timtheloon]

An X-ray was taken, but unfortunately it did not show the cause of the error (the resolution was not enough)
I'm looking for another x-ray..

I like the thorough examination are you willing to upload the xray results I find this very interesting

 

[sax]

Sold as bad in another topic! Please close this thread!