Support Gotek AMIGA 500 and 500+ printed in 3D

[cocomocho]

Full support Gotek for AMIGA 500 and 500+ printed with ABS plastic white, I only have this unit printed, but I can print many more units. It would make a list of interested and as they are going to have the units printed, they would be sent to each person. Support price is 8€ (before 20€) + shipping, Paypal.

Interested:

sirlemonhead ------- 1 piece ------- Payment ------- Printed -------- Send
corigon ------------ 2 pieces ------ Payment ------- Printed -------- Send
jcarvalho ---------- 1 piece ------- Payment ------- Printed -------- Send
kinchan------------ 2 pieces ------ Payment ------ Printed --------- Send
botialoach --------- 1 pieces ------ Payment ------- Printed ------- Send
cercamon --------- 2 pieces ------ payment ------- Printed ------- Send
Nidunite ----------- 1 piece ------- payment ------- Printed ------- Send
Starglider --------- 1 piece -------- payment ------ printed -------- Send
AndrewM --------- 1 piece -------- payment ------ printed -------- Send

 

[cocomocho]

price drop!!

 

[mrr19121970]

are you able to produce at a higher resolution ?

 

[cocomocho]

are you able to produce at a higher resolution ?

If, although it is at a higher resolution, 0.15mm the maximum resolution I can do is 0.1mm, they have 100% filler to make it resistant.

 

[CrazyBob]

With 50% infill it's strong enough and 0.1mm gives a nice finish.
These look good too

 

[cocomocho]

up!!

 

[davideo]

up!!

Again time for another de-bump.

 

[cocomocho]

up!!

Again time for another de-bump.

i´m sorry

 

[cocomocho]

Still for sale

 

[cercamon]

Can you show us a picture of a mounted gotek unit in an A500? Does your project still needs cuts in the top of the Amiga case? Thanks.

 

[cocomocho]

Can you show us a picture of a mounted gotek unit in an A500? Does your project still needs cuts in the top of the Amiga case? Thanks.


Inviato dal mio iPad utilizzando Tapatalk

Tomorrow I show a demonstration of how it would be in a case that I have, I do not currently have any Gotek, but to see how it would look. There is no need to cut anything on the top of the computer case

 

[cocomocho]

Added 2 more photos

 

[SalvoB]

Intresting, please write me shipping costs and I'll think about it

 

[kaosboss]

interested. let me know the shipping cost

 

[sirlemonhead]

Interested too, if you can also let me know shipping cost to Ireland.

 

[cercamon]

Thank you for the pictures. I'm not sure you can still operate on buttons or plug in a usb stick with the gotek drive in and the top case closed. Did you keep these issues into consideration when you designed the plastic crate? Thx


Inviato dal mio iPad utilizzando Tapatalk

 

[fabbie54]

Nice. Have you considered doing the same for the A2000, that covers the (larger than usual) floppy bay? Typically, people have been using 3D printed fillers with Goteks to fill the gap.

 

[jcarvalho]

Interested pending shipping costs to Portugal
Interested also for A2000 when ready
Enviado de meu Redmi Note 3 usando Tapatalk

 

[warr8or29]

Interested, what's the shipping cost to france please ?

Envoyé de mon SM-T580 en utilisant Tapatalk

 

[cocomocho]

If in fact it is designed so that you can press the buttons and can put the pendrive without problem, I have already sold many pieces of these and everything well, the problem is that I ran out of stock gotek and I could not take a picture with one installed but it fits well .

Forgive me for not answering before, I have been a few weeks on vacation and I have not been able to answer the messages.

- - - Updated - - -

Nice. Have you considered doing the same for the A2000, that covers the (larger than usual) floppy bay? Typically, people have been using 3D printed fillers with Goteks to fill the gap.

Yes, I have a filling made for the gap between the gotek and the casing.