For Sale Amiga A4000 Reproduction Case Pre-Order Closed

[Ordyne]

I might be OK with that. Is the staining on an area that would otherwise be covered by a faceplate or not visible once assembled?

Are you selling seconds at a discounted rate? If so, what is the cost with all included options?

Thanks again

I will drop you a PM

 

[MarkJPK]

Declaring interest.

---

(Marked as sold/completed by Ordyne)

 

[MarkJPK]

Hi,

If you are considering a 4th batch I would like to declare interest and am happy to send you a deposit.

Declaring interest.

With the following Options:
+Honeycomb vented expansion slot covers £10
+Honeycomb vented Zorro card slot covers £12
+PCB Insulation sheet set (Sheet under main board and one that sits behind 3.5" drive's and Zorro daughter card) £10
+SD to IDE PCB Expansion slot mount (does not come with PCB, PCB available on ebay etc) £10
+Rear IO sticker £12

Thanks
Mark

 

[Ordyne]

Hi Mark,

Happy to start up a new batch and put a time limit on it so you’re not sitting around indefinitely. To be fair they seem to start filling up once a few people have taken the plunge!

 

[MarkJPK]

Hi Mark,

Happy to start up a new batch and put a time limit on it so you’re not sitting around indefinitely. To be fair they seem to start filling up once a few people have taken the plunge!

Excellent - let me know when you need a deposit!

 

[Ordyne]

OK, I will be making changes to how the pre-order is going to work as the whole idea of it is to secure numbers and that hasn't really worked as a lot of people have dropped out or not responded when it has come to the stage of taking deposits when enough people have joined to start the run.

It has also been apparent that the price has needed to go up on these for some time, in fact I would go as far as to say I probably priced it too low to start with but I have stuck to the initial pricing for the runs so far, there are a lot of hours put into making these, it needs to go up but here is what I am going to do.

I will start a pre-order with an up front deposit of £150, the deal is you get the case at the same original price of £350 + cost of extras etc. I will give an end date for the pre-order rather than waiting for X number of people and will start making the run of cases regardless of how many people have joined the pre-order so there in no indefinite waiting. So what's in it for you? Only people on the pre-order will get the case at £350, once the pre-order is closed any extra cases made (I normally make a batch of 20 or 25 cases) left over will be sold at £400. If you back the build then you get the discount, the deposits are not refundable BUT if for whatever reason I did not deliver you would obviously be refunded.

I will be amending the main page of the thread to show this, if anyone who has declared interest no longer wants to jump on board I totally understand.

 

[saft6luck]

Declaring interest.

---

2 cases with

• Vented Covers
• Vented Zorro Covers
• ZULU SCSI
• Insulation Sheets
• Sticker

---

(Marked as sold/completed by Ordyne)

 

[andrean]

Declaring interest.

---

Declaring interest in the case with all the listed extras included, provided I can fit the A4000 RevB replica board into it.

---

(Marked as sold/completed by Ordyne)

 

[Ordyne]

Declaring interest.

---

Declaring interest in the case with all the listed extras included, provided I can fit the A4000 RevB replica board into it.

If the board fits in a standard a4000 case then yes.

 

[andrean]

If the board fits in a standard a4000 case then yes.

Thanks, I verified that in the meantime, seems to be of the same dimensions. Interest still declared.

 

[amienslaver]

Acill's replica of A4000 fits the case perfectly. If this one is of the question.

 

[Boing-ball]

Acill's replica of A4000 fits the case perfectly. If this one is of the question.

Can confirm that ACILL, Saft6Luck and original Commodore 4000D boards will fit Ordynes new case. I have just tried each in a project.

 

[Boing-ball]

Declaring interest.

1 x Case in standard White Cream colour with the following:

Honeycomb vented expansion slot covers £10
Honeycomb vented Zorro card slot covers £12
PCB Insulation sheet set (Sheet under main board and one that sits behind 3.5" drive's and Zorro daughter card) £10
CF to IDE PCB Expansion slot mount (does not come with PCB, PCB available on ebay etc) £10
SD to IDE PCB Expansion slot mount (does not come with PCB, PCB available on ebay etc) £10
Zulu Scsi PCB Large Expansion slot mount (does not come with PCB) £10
USB Expansion Slot Plate £4
Rear IO sticker £12

Cheers.

---

(Marked as sold/completed by Ordyne)

 

[janderson]

Hello, I have two A4000's that need only the top covers. Would you happen to have any available? Or be willing to manufacture/sell top covers?

 

[amigasquirrel]

Hi there, does anyone have pictures of how this case looks with the aluminium front panel supplied by PRS?

 

[suavek]

Interest withdrawn. (was previously declared here)

Got this case 2nd hand. Thank you.

 

[Ordyne]

Hello, I have two A4000's that need only the top covers. Would you happen to have any available? Or be willing to manufacture/sell top covers?

I have the top covers available, they cost £150 each.

 

[janderson]

I have the top covers available, they cost £150 each.

I am definitely interested in two. Are they painted beige?

 

[Ordyne]

I am definitely interested in two. Are they painted beige?

Yes they are

 

[Robert_G]

So this is a test of the latest feature request. This makes a change so the drive tray is fastened from the inside of the case. The main advantage of this is that you don’t need to remove your front cover to take the drives out. Just remove the two screws which are now on the inside, pull back the tray to release it from the clip in the bottom of the case and then lift out.

Following photo’s are just from a test.

View attachment 2513200


View attachment 2513202


View attachment 2513203

If you want this feature let me know!

Whether the new batch will have a modification of drive tray (inside screws)?