Picasso Graphic PCB for A500 - A2000 - A4000 - GBA1000. 1st Batch

[cpiace64]

payment 20,50€ sent

 

[Tuxbar81]

payment 20,50€ sent

Thanks a lot! Table updated.

 

[viserys23]

Payment made.

 

[cpiace64]

i have a dubt, the edge connector for use with a500, where i can buy, on a1k.org?

 

[Tuxbar81]

i have a dubt, the edge connector for use with a500, where i can buy, on a1k.org?

I have searched for this connector, but I have found nothing... I'll ask to Matthias where we can find this connector needed for the A500.

 

[hese]

You get the 86 pin edge connectors from here:
http://www.jameco.com/1/1/58299-50-86c-10-wirewrap-rectangular-connectors-card-edge.html

 

[Tuxbar81]

You get the 86 pin edge connectors from here:
http://www.jameco.com/1/1/58299-50-86c-10-wirewrap-rectangular-connectors-card-edge.html

Thanks for the link, but for the A500, The needed connector is the right angle version.

I have actually 14 unit of the86 pins connector but it's not the right angle, and it's needed for the Thylacine of the GBA1000.

 

[hese]

You need the right-angle version only if you want to mount the graphics board horizontally.

 

[Tuxbar81]

You need the right-angle version only if you want to mount the graphics board horizontally.

You're right, but it's not very convenient if your A500 is into its original case to have a graphic board connected vertically! If you put it into a tower, it's perfect!

 

[hese]

It's also not very convenient to leave the board naked on the side of the A500 at any angle! If you put it in a case, it's better!

 

[hese]

@Tuxbar81

Would this be better?
http://www.toby.co.uk/content/catalogue/products.aspx?series=802-R-xx-S-R

 

[Tuxbar81]

@Tuxbar81

Would this be better?
http://www.toby.co.uk/content/catalogue/products.aspx?series=802-R-xx-S-R

Yes, I think that should be perfect! The one shown here is for a 12 pins version.
Perhaps there is the one we need!

 

[hese]

The one shown here is for a 12 pins version.
Perhaps there is the one we need!

86-pin should also be doable, quote from the page: "Other sizes are available but may be subject to MOQ - please contact us".

 

[JanciB]

The one shown here is for a 12 pins version.
Perhaps there is the one we need!

86-pin should also be doable, quote from the page: "Other sizes are available but may be subject to MOQ - please contact us".

They are doing 86 pin too:

http://www.toby.co.uk/datasheets/section5/802-R-xx-S-R.pdf?revDate=

J.

 

[Tuxbar81]

The one shown here is for a 12 pins version.
Perhaps there is the one we need!

86-pin should also be doable, quote from the page: "Other sizes are available but may be subject to MOQ - please contact us".

Yes, I had seen this mention!

- - - Updated - - -

The one shown here is for a 12 pins version.
Perhaps there is the one we need!

86-pin should also be doable, quote from the page: "Other sizes are available but may be subject to MOQ - please contact us".

They are doing 86 pin too:

http://www.toby.co.uk/datasheets/section5/802-R-xx-S-R.pdf?revDate=

J.

I'm going to contact them.
Before, I'll need to know how many connectors we'll have to order to see if we can have a good price!
So, if you're interested, please, let me know here.

 

[hese]

Three connectors for me.

 

[viserys23]

Interested in 2.

 

[MatthiasH]

In my archive a few posts above (hint: read the fine manual - or what comes close to it )you will find a part list with the appropriate digikey-number for the right angle edge-sot:
[TABLE="width: 309"]
[TR]
[TD="class: xl63, width: 309"]ECC43DCAI-S189-ND
[/TD]
[/TR]
[/TABLE]
But minimum quantity is 10, so you have to group up!

Best regards Matthias

 

[Tuxbar81]

In my archive a few posts above (hint: read the fine manual - or what comes close to it )you will find a part list with the appropriate digikey-number for the right angle edge-sot:
[TABLE="width: 309"]
[TR]
[TD="class: xl63, width: 309"]ECC43DCAI-S189-ND
[/TD]
[/TR]
[/TABLE]
But minimum quantity is 10, so you have to group up!

Best regards Matthias

Great! Thanks a lot Matthias. Some members here wanted this connector!

Actually, hese wants 3 connectors and viserys23 wants 2. If I remember well, piacc64 wants also 1. I'll take one.
So, normally, 3 are available for an order of 10.

Best regards,
Franck.

 

[Tuxbar81]

Sorry for my late. Lot of work before the summer time...

I have contacted Digi-Key for the right angle 86 pins connectors. They are not in stock & the delay is about four weeks.
I'm going to order them.

The parcels are almost ready. I only have to add the Xilink IC. The parcels for members who don't want the right angle connector could be posted very soon.
The price for one piece is: 8.182€.
The shipment is free for an order higher than 65€... cool!
If I understand well, no entrance taxes. We'll when they will be arrived.