Recent content by MatthiasH

Do you know which firmware is used on your accelator card? The latest version of MapROm has IDETweak integrated...

There are still boards from the official website available. https://webstore.kryoflux.com/catalog/ These boards come with a full 2years warranty. Unfortunately shipping to US, New Zealand and Australia is expensive at the moment. :(

One comment from me - the developper of this card: This card is still commercial available boards at the official webstore: https://webstore.kryoflux.com/catalog/product_info.php?products_id=56 These boards come with a warranty! 165€ is generally not much for a diy-project with this small...

Great work! What a nice design! As an owner of an "original" AA3000 I can give you some hints: The blank-signal for the videoconnector is unconnected on the original AA3000-MoBo. Check the A4000 schematic to do the same "conversion" of the Blank-Signal to Lisa with the Videoport. It seems...

Great work! The board layout looks very fine! Some minor hints: You should think of putting the IDE-GALs in THT sockets. SMD-Sockets are poor to solder by hand. THT are much more robust. If the IDE-GALs are removable you could easily play with the PIO2-hacks, which are sometimes incompatible...

Unfortunately not. Cybergraphics support was planed and runns on my Amiga. But it is instable and I did not get sufficient support from the CgFX-team to fix the problem :(

Hi, at the German a1k-forum I developped together with Georg Braun a ZII/A500 - variant of his 2MB GBAPII++ card. Its available for a year now, but Kryoflux and I proudly present a "Black Friday - Campaign": ZII-Version for 199€ + shipping till Sunday! It's brand new, industrial made, confirms...

Hello! I proudly present the new RTG-graphics board for all Bigbox-Amigas and the Amiga500: The GBAPII++ is now commercially available at kryoflux (<-link). We ship worldwide and VAT applies only for EU-countries (customs fees must be paid by the customer). The GBAPII++ is a ZorroII-card...

This is a bit impertinent. This is my design and driver. The copyright for all my products is "Free for non comercial use". I dont know your PCB-costs, but these pcbs cost me 2€ each (+ shipping and customs from China makes it 3€) and the parts-costs are ridiculous. You could have at least asked...

The BlindGerMan has written a review for this board: http://www.a1k.org/forum/showthread.php?t=48464&highlight=etwas+andere+Grafikkarte currently Im planing to launch a commercial product from this project, which will be available before x-mas (hopefully) ;). Best regards Matthias

In my archive a few posts above (hint: read the fine manual - or what comes close to it ;) )you will find a part list with the appropriate digikey-number for the right angle edge-sot: ECC43DCAI-S189-ND But minimum quantity is 10, so you have to group up! Best regards Matthias

It allready did! http://www.a1k.org/forum/showthread.php?t=40955 BTW: R32 should be 1Ohm too. Otherwise you will get horizontal "ghost stripes" at black boxes on the screen. Regards MAtthias

OK, here is a fixed partlist, containing all files, schematics and jed to construct this thing: I changed the parts at line 6, 28 and 29. The whole thing works at my place. HEre is an untested adapter to make this thing work in the GBA1000...

As I sad this will become a commercial product with warranty and so on. Hopefully selling will start in 2015! Btw: I made a mistake in the parts too: The SMD-pinheaders in my list do not fit! They are to broad for the solder pad. Regular 2x10-Pinheader should fit! Regards Matthias - - -...

Thank you! Be aware, that R8 should be just a 0Ohm-Bridge and C11 can be ommited! IC8 should be TI LM3334M(X) and NOT LM334SM(X). Best regards Matthias