C
Cozzer79
Guest
Price drops on the remaining items 
- Status
C
Cozzer79
Guest
C
Cozzer79
Guest
Chinon FZ-357A sold outside of AmiBay
C
Cozzer79
Guest
C
Cozzer79
Guest
RapidRoad USB sold outside of AmiBay
C
Cozzer79
Guest
Benq 702A 17" monitor and adapter sold outside of AmiBay
C
Cozzer79
Guest
2nd Ktrl32 Control Pad sold outside of AmiBay - open to near offers on Nightlong to clear the lot
C
Cozzer79
Guest
All items now sold - just awaiting feedback on the remaining items sold through AmiBay Thanks all!
Thanks all!Parcel arrived at the beginning of the week but I did not have time to open it until now.
Everything ok. Positive feedback left. Thank you.
Everything ok. Positive feedback left. Thank you.
Payment received and feedback left. I'll get that packaged up this evening and on its way to you tomorrow; I'll confirm tracking then.
Not had your address yet that I can see - I'll send a chaser later if I've not got it by then. Thanks!
Heavily expanded A1200 now split
A1200 mobo received
tested it I was like why is it not working :double oh yeah no 020 cpu need a accelerator!!!
one question when does it start graphic glitching????
positive feedback left too
A1200 mobo received
tested it I was like why is it not working :double oh yeah no 020 cpu need a accelerator!!!
one question when does it start graphic glitching????
positive feedback left too
Last edited:
C
Cozzer79
Guest
lol - yup, no CPU fitted!
With an Indivision AGA fitted, the glitches start from cold boot - with the cable attached to it it was pushing g the right side of Lisa up, but without it fitted, I've not had it do anything worrying after several hours. Most likely a dry joint so it'll need reflowing eventally if you're not going to put an Indivision on it
With an Indivision AGA fitted, the glitches start from cold boot - with the cable attached to it it was pushing g the right side of Lisa up, but without it fitted, I've not had it do anything worrying after several hours. Most likely a dry joint so it'll need reflowing eventally if you're not going to put an Indivision on it
A1200 mobo received
tested it I was like why is it not working :double oh yeah no 020 cpu need a accelerator!!!
one question when does it start graphic glitching????
positive feedback left too
it been on for a while now and still no glitches maybe it was that last magic push you give it 
Ill try it with an indy to see what happens
Ill try it with an indy to see what happens
Received parcel, very good shipping protection and packaging. First test booted up the BPPC but did not boot with B-Vision attached. I assume my PSU needs an update as it only provides 4A at 5V. Ordered a 12A/5V variant and will inject additional 5V to Floppy-Power-Port. Testing can start in two weeks from now as I'm busy until then, but assume everything will be fine. Great card, thanks for the deal.
C
Cozzer79
Guest
Hi matey - it needs a biiiiggg PSU; Stachu recommended at least 8A on the 5V rail. On my board, I added wires for 5V, 12V and Ground from the underneath of the power supply connector to the rear of the floppy power connector - a common mod to improve power distribution. Injecting power into the floppy connector is another popular method though. Not all boards are equal! I know the 12V isn't necessary for this, but I had numerous 12V fans running from the floppy connector.
C
Cozzer79
Guest
We're dealing with this in PM - no need to drag it out here.
Unfortunately the BVision is showing loose pins and doesn't work. 160W PSU Installed and enough power is available.
C
Cozzer79
Guest
Refunded for BVision - it was in working order when sent, but for whatever reason isn't anymore.
- Status
